Hp Laptop Wont Boot Windows 10
When it is turned on it does not go past the welcome screen that says HP press escape...to start up. On the Choose an option screen, click Troubleshoot. You might be instructed to replace or service a component. Remove any screws that connect the panel to the computer. http://ocvninfo.net/hp-laptop/hp-laptop-wont-start-up-windows-10.html
On the Choose an option window, click Troubleshoot. Reply 0 0 amielu Top Student Posts: 6 Member Since: 01-11-2012 Message 9 of 28 (41,151 Views) Report Inappropriate Content Re: my computer will not get past the start up blue Follow these steps to use the UEFI tests to check for problems: Step 1: Run the System Quick Test in UEFI (All-in-Ones) The System Quick Test takes about 10 minutes to After the back up I just formatted the internal hdd and used recovery dvds to restore the factory settings.You can also do a fresh install or whatever you want because the
Hp Laptop Wont Boot Windows 10
Read more Register · Log In HP Support Forum Home > Desktops > Boot > Can not get passed HP logo screen when powering on Search the Community To learn more about troubleshooting blue screen error messages, see Troubleshooting Blue Screen Error Messages that May Display During Startup or Boot (Windows 10, 8, 7). Figure : The HP PC Hardware Diagnostics UEFI screen Click Quick Test.
I don't have any other pcs to do a back up so had to use that usb flash drive or live cd(needs any usb flash plugged in) with linux on it. I don't have any other pcs to do a back up so had to use that usb flash drive or live cd(needs any usb flash plugged in) with linux on it. This link takes you either to a support document that contains troubleshooting steps for your computer’s issue or to the general troubleshooting steps provided in Step 3. Hp Desktop Wont Boot Past Hp Screen Select Repair Your Computer, and then press Enter.
The CMOS battery backs up the time and other settings when the computer is turned off. Hp Computer Won't Boot Past Blue Screen Remove media from internal drives, and remove any recently added internal hardware. Press and hold the power button until the computer turns off completely. Search all support All Support Software, Drivers and Updates Troubleshooting How to Product Information User Guides Cancel Example: “Laserjet P1102w driver” or “HP Pavilion 17-f002na will not turn on” Loading Results
Hp Computer Won't Boot Past Hp Screen
If the startup problem still exists, continue to the next step. http://h30434.www3.hp.com/t5/Notebook-Boot-and-Lockup/Can-t-Get-Past-Manufacturer-Boot-Screen/td-p/264843 Use the arrow keys to select Yes or OK, and then press Enter. Hp Laptop Wont Boot Windows 10 Figure : A 4-pin drive power header two drive power connectors on the system board that are facing the opposite direction All-in-Ones and HP TouchSmarts - troubleshooting when the hard drive Hp Laptop Wont Go Past Startup Screen Step 2: Perform a hard reset Many startup errors and other problems can be resolved by decreasing the amount of power stored in hardware components.
If all of the above steps have been tried and the computer does not turn on, the computer might require service. navigate here If you cannot find a symptom that matches your computer's symptom, then continue to Step 3 for steps to check if the hard drive is detected in BIOS. Under the Advanced or Diagnostic tab you should find the facility to run tests on both the Hard Drive and Memory. If the computer still does not turn on, unplug the power cord from the wall outlet and continue troubleshooting. Hp Laptop Stuck On Startup Screen
If the computer does not have an AC adapter, skip to step 11 in these instructions. I did other tests over again and the memory test passed, but the hard disk test and startup test failed. If the startup problem is gone, troubleshooting is complete. Check This Out Step 2: Reseat the hard drive in an All-in-One or HP TouchSmart To reseat the hard drive, perform the following steps: note: For detailed instructions, open HP Customer Support, enter the
If you cannot find a symptom that matches your computer's symptom, see Step 4: Run Hardware Diagnostics tests. Hp Laptop Wont Boot Past Welcome Screen Figure : System Recovery Options (The window on your computer might look different) Click Startup Repair. If the error is still displayed, go to Troubleshooting other issues with computer not starting.
Disconnect all non-essential devices (printers, scanners, external hard drives, and similar). Unplug the power cable, then press the Power button. Status BAD, Backup and Replace To resolve SMART error messages, see Hard Drive Failure Errors. Computer Wont Load Past Hp Screen Figure : HP logo on genuine HP AC adapter Determine the adapter wattage by looking near the bottom of the adapter.
Ask the community! I press finish, it shuts down. Step 1: Reset the BIOS in All-in-Ones Reset BIOS to make sure the BIOS settings are correct: In the Computer Setup window, Use the left and right arrow keys to select Disk boot failure To resolve disk boot failure error messages, see Step 3 for steps to check if the hard drive is detected in BIOS.
The computer locks up at the HP or Compaq logo screen or the Windows loading screen If the computer locks up at the HP or Compaq logo screen or the Windows Step 2: Run the System Extensive Test in UEFI (All-in-Ones) System Extensive Test can take two or more hours to complete. Figure : Example of one type of side panel. A defective AC power adapter might not charge the battery, and this could prevent the computer from starting on battery power only.
Figure : Refresh your PC screen Wait until Windows completes. If the computer does not turn on, continue using these steps. If Windows does not open, repeat steps one through six to open the System Recovery Options window, and then continue to step ten of these instructions. and Product No.
Find Solutions, ask questions, and share advice with other HP product owners. From the UEFI main menu, click System Tests, then click Fast Test. If components are defective and the computer is under warranty, Contact HP for further assistance. When recovery starts, continue using the steps to complete recovery.
note: You might want to update the BIOS if an update is available for your computer model. To reduce the chance of ESD damage, work over a noncarpeted floor, use a static dissipative work surface (such as a conductive foam pad), and wear an ESD wrist strap connected Find Solutions, ask questions, and share advice with other HP product owners.